VIFLY WhoopStor 3 – 1S Battery Storage Charger and Discharger Original price was: ₹5,250.00.Current price is: ₹3,150.00. incl.GST
Back to products
BetaFPV Pavo 20Pro Drone ₹31,500.00 – ₹57,750.00 incl.GST
-3%
Click to enlarge

MicoAir H743 AIO V2 45A AM32 3-6S Flight Controller & ESC

Original price was: ₹10,500.00.Current price is: ₹10,185.00. incl.GST

Authorized Dealer of Top Drone Brands

Repair and Maintenance Support

Fast Shipping Across India

5 in stock

5 in stock

Compare
Add to wishlist
19 People watching this product now!

Payment Methods:

Description :

SPECIFICAIONS:

Flight Controller

  • MCU: STM32H743VIH6, 480MHz, 2MB Flash
  • IMU: BMI088+BMI270
  • Baro: SPL06
  • TF Card Slot
  • 7x UART
  • 9x PWM
  • 1x I2C
  • 1x SWD
  • 2x ADC (VBAT, Current)
  • 1x LED Strip
  • 1x Beeper
  • USB Type-C
  • BEC 5V 2A output (for controller, receiver, GPS, optical flow or other devices)
  • BEC 12V 2A output (for DJI O3/O4/O4 pro)

ESC

  • Firmware: AM32_F4A_4IN1_F421_2.17
  • PWM Freq: 48KHz
  • ESC Protocol: PWM/DShot300/DShot600 (support BDShot)
  • Continuous Current: 45A * 4
  • Voltage Support: 2-6S (5.6V-27V)

Tutorial: How to Configure and Update AM32 ESC on MicoAir743-AIO

Voltage&Current Monitoring

Ardupilot PX4 Betaflight INAV
Voltage Factor 21.12 21.12 211 211
Current Factor 14.14 14.14 707 707

UART Mapping (Ardupilot)

  • SERIAL0 -> USB
  • SERIAL1 -> UART1 (MAVLink2, DMA-enabled)
  • SERIAL2 -> UART2 (DisplayPort, DMA-enabled)
  • SERIAL3 -> UART3 (GPS, DMA-enabled)
  • SERIAL4 -> UART4 (MAVLink2, DMA-enabled)
  • SERIAL5 -> UART5 (DMA-enabled)
  • SERIAL6 -> UART6 (RCIN, DMA–enabled)
  • SERIAL8 -> UART8 (DMA–enabled)

UART Mapping (PX4)

  • ttyACM0->USB
  • ttyS0->TELEM1 -> UART1
  • ttyS1->GPS2 -> UART2
  • ttyS2->GPS1 -> UART3
  • ttyS3->TELEM2 -> UART4
  • ttyS4->TELEM3-> UART5
  • ttyS5->RC -> UART6
  • ttyS7->TELEM4/SERIAL4 -> UART8

RC Input (Ardupilot)

The default RC input is configured on the UART6. The SBUS pin is inverted and connected to RX6. Non SBUS, single wire serial inputs can be directly tied to RX6 if SBUS pin is left unconnected. RC could be applied instead at a different UART port such as UART2, UART4 or UART8, and set the protocol to receive RC data: SERIALn_PROTOCOL=23 and change SERIAL6 _Protocol to something other than 23.

OSD Support  (Ardupilot)

The MicoAir743v2-AIO supports OSD using OSD_TYPE 5 (MSP_DISPLAYPORT).

VTX Support

The SH1.0-6P connector supports a DJI Air Unit / HD VTX connection. Protocol defaults to DisplayPort. Pin 1 of the connector is 12v so be careful not to connect this to a peripheral requiring 5v.

PWM Output

The MicoAir743v2-AIO supports up to 9 PWM outputs.

Channels 1-8 support DShot/bi-directional DShot.

(currently PX4&INAV not support BDShot function)

PWM output share grouped and every group must use the same output protocol:

1,2,3,4 are group 1

5, 6 are group 2

7,8, 11are group 3

Note: PWM11 is the “LED” pin. If this is configured for serial LED use then PWM 7 and 8 can only be used as serial LED also.

Compass

The MicoAir743v2-AIO doesn’t have a built-in compass sensor, but you can attach an external compass using I2C on the SDA and SCL connector.

Physical

  • Mounting: 25.5 x 25.5mm, Φ3mm
  • Dimensions: 36 x 36 x 8 mm
  • Weight: 10g
Weight 320 g
Dimensions 5 × 4 × 4 cm
Brand MicoAir